When Your Elevator Controller Goes Obsolete: The TAC 20 Story

Nov 2, 2026

If your building has a TK Elevator TAC 20 or TAC 22 controller, the manufacturer has stopped making its key circuit board, and the clock on easy repairs is running.

These controllers are not ancient. They went into hydraulic elevators across North America in the 2000s and 2010s, so many owners are surprised to hear the word “obsolete” at all. This post covers what happened, why, how long the equipment can keep running, and what it means when something breaks. It also covers the TK Icon, where the public record is much thinner than for the TAC 20.

What the TAC 20 and TAC 22 are

The TAC 20 is a solid-state, microprocessor controller built for hydraulic elevators, and the TAC 22 is its close sibling. It was introduced around in the early 2000s, when Thyssen acquired Dover. It followed Dover’s DMC-I controller, and some early units installed in the Thyssen Dover era were really DMC-I controllers with a Thyssen label and Dover boards inside.

That lineage matters for repairs. A TAC 20 can contain boards from different generations, so what you can source depends on which version is in the machine room.

 

Why it became obsolete

The trigger was a manufacturer letter dated January 6, 2025. The letter told building owners the TAC 20/TAC 22 CPU board had been officially discontinued, and that TK was retiring the product line.

TK has said the same in its own words. In a 2025 modernization article, a TK Elevator sales director says the company recently declared TAC-20, its former hydraulic controller package, obsolete, after doing the same to the Dover DMC package a couple of years earlier.

The pattern is common in this industry: the manufacturer moves to newer controller platforms, stops building the core board, and the older line becomes a parts-and-repair problem instead of a supported product. TK’s current hydraulic offering, for example, includes modernization packages such as H-Power, which the company says can modernize virtually any hydraulic system, TK or not.

How long it has been obsolete, and how long it will last

The TAC 20 has been officially obsolete for about ten months as of this writing (November 2026), counting from the January 2025 letter. I could not find a published end-of-support or sunset date, so nobody outside TK can say exactly when the last spare will ship.

What the sources do agree on is that the supply is finite. Colley Elevator puts it bluntly: parts still exist, but when they are gone, they are gone. Because so many TAC 20 and TAC 22 units were installed, a few failures at the same time would pull from the same limited pool of spares. 

A practical reading: the equipment can keep running for as long as its boards hold up or can be repaired, but every year the odds of a repair taking days instead of hours go up.

What it means for fixing the equipment

Repairs get slower, less predictable and more dependent on workarounds. The main effects reported by contractors and technicians:

  • Third-party boards. Some outside manufacturers stock boards, and forum posters name distributors such as ECI America and World Electronics. These parts are aftermarket and may differ from the OEM version.
  • Board-level repair. A few solid-state repair shops will fix failed boards. Colley warns that repairs sometimes fail or take several attempts, which means extra downtime.
  • When you swap a board, you may need updated or original software to load onto it. If the original program was never backed up, that can stall a job.
  • Shared spare pool. Everyone servicing TAC 20 and 22 units is drawing on the same shrinking stock, so a rare failure can turn into a long outage.
  • Contracts and pricing. One owner-side guide notes that obsolescence gives the OEM pricing power over repairs and that some service contracts exclude “obsolete” parts. It also points out that the word is often applied by the service provider without a published end-of-support date, so owners should ask for a specific reason a part cannot be sourced.

In short, the controller does not fail on a schedule, but when a CPU or interface board does, the fix may be a hunt for a spare rather than a simple replacement.

The TK Icon: what I could and could not confirm

I could not find a public source that says a TK Icon controller has been declared obsolete, and I would rather say so than invent dates and reasons. The documented TK obsolescence announcements I found are for the TAC 20/22 line and, earlier, the Dover DMC package.

If you are dealing with an Icon, the questions to put to TK or your contractor are the same ones that apply to the TAC 20:

  • Has TK issued a written discontinuation or end-of-support notice, and what is its date?
  • Which specific boards are discontinued, and which are still supplied?
  • Is there a published last-time-buy or support-end date?
  • What are the repair, exchange and modernization options for this exact controller?

What to do now

Plan for a controller modernization instead of waiting for the failure that forces one. Practical steps for owners and for companies that service these units:

tac20